Recent content by multi

  1. M

    no speedo gear

    Hello all of you. I have zf 4hp22 which came from a jaguar. i changed the bell housing to rover type. but there is no speedo gear on the transmission. is it possible to convert it to mechanical speedo gear ? Or does any zf 4hp22 come with mechanical speedo gear? Best Regard Multi
  2. M

    4,6 heads flownumbers.

    Hello everybody. is there any who is able to share standard 4,6 cylinder heads flownumbers. best regards Multi
  3. M

    Edelbrock performer inlet manifold

    Now i got hold of rover inlet manifold, and there is no steamholes from the water channel to the thermostat housing. so i thing i just will forget all about it. ;) cheers
  4. M

    Edelbrock performer inlet manifold

    Hello all of you. I fell over an article on facebook about edelbrock 2198 manifold which was missing two holes/passages from the water channels to the thermostat housing. but now i am not able to find the article again. The Rover ,Pontiac and Buick manifold would have these holes. the point is...
  5. M

    timing gear

    Thank you very much. i did put the front end on a pair of ramps. when heating the engine up, it was a hit. sure i got it now. best regards. Multi
  6. M

    timing tape

    Can anybody tell me the exact diameter of the standard p6 crank damper . so i can make a timing tape . its a little hard to do a exact measure when it is sitting in the car. thank you in advance, best regards. multi
  7. M

    timing gear

    Hello everyone. I have changed the timing gear . and now i have cooling problems. the timing is spot on. i have flushed the radiator and engine. controlled top dead center. the positive stop way. it was also all right. cooking the thermostat. water seams to to be circulating. i have testet for...
  8. M

    to tow or not to tow

    is it possible to tow a borg warner equipped car without damaging the gearbox. is there a max towing speed and distance.? Best regards Multi
  9. M

    borg warner 35 weak reverse and no top gear.

    Hello Harvey. Well it ended up by taking the engine out of the car because i noticed a rusty coreplug and i knew from earlier that the timing chain was worn. then i had the chance testing the gearbox on the engine. so i turned the gearbox that have a weak reverse and no topgear, upside down...
  10. M

    any performance in P6 exhaust manifolds ?

    Thank you. that was the answer i was looking for. you see aim planning to make a 200-220hp engine so now i know that those 3500S manifold will not be the restriction on that :thumb: Cobraboy: i really like the dyno graph. must be a lot of fun to drive. lots of torque from 1400rpm. but what is...
  11. M

    any performance in P6 exhaust manifolds ?

    Hello everybody. I have these P6 exhaust manifolds . ( see pickture) I really like the look of them but i understand that they are a bad choice in a performance perspective. But where are the limit? does any have some experience with them in a high performance matter? is possible to port them...
  12. M

    core plugs

    now i know. a few ways how not to do. ;) I found out that grinding a small groove in the side part of the plug, paying attention nut to grind thru into the head. makes it possible to tilt the plug when the spot where has been grinded thin collapses. then it is possible to grab it with a pair of...
  13. M

    core plugs

    Hello everybody. is there a smart way to remove the small core plugs located in the cylinder heads? looking foreward to hear from you. Best regards Multi
  14. M

    borg warner 35 weak reverse and no top gear.

    Hello Harvey. i have just taken the gearbox of the car again. i had another broken gearbox from where i took the bolt and the rear servo. but it did not help. which pipe goes to the rear clutch . i will take a close look at the valve body and the oil pump which i took off to chance the axle...
  15. M

    borg warner 35 weak reverse and no top gear.

    Hello Harvey. I took the oil pan off the transmission this evening . the pipes seems to be sitting alright. Then i took the pipe to the rear servo off and did an air pressure test of the rear band and servo, i saw that the servo did wiggle a little. i decided to take off the servo to check the...
Top