Search results

we have a p6 3500 s that got an lt77. the car has vibrations, from 130 km/h. of course we have already fixed the usual factors: wheels, drive shafts, cardan shaft. my question is: can the installation angle (the bracket from the lt77 is self-made) be the cause?

a year ago we installed on front axle & rear axle the superflex.co.uk blue. the customer says it rumbles and i can confirm that. which rubbers are nice soft? the orgiginals from wadhams?

I am looking for a baseunit for restoration. can still roll, but does not have to.... I can't find anything on the continent

I'm looking for 4 good wings in burnt gray with original paint. the paint may be matt , but they should be so that the paint is worth preserving best regards jorgen

i have a strange problem with the ignition (i think). first: everything is new! engine, ignition (fingers, contacts, capacitor, cap, spark plug cable,), carbs. but not the wiring harness or something like that. the car runs perfectly for about 10 minutes. then ignition failures begin and the...

I would like to retrofit oil pressure and oil temperature. I should know what kind of screw thread this is. Please take a look at the attached picture.

where are the sheets mounted on the rocker arm ? front, back, on both sides? best regards jorgen

I would like to have my rear axle differential overhauled and strengthened (I have a 4.6 liter engine). I'm looking for a company that does it well. best regards jorgen

every time i accelerate fast or drive faster, the ignition has a strong suspension. The cart then jerks, and goes out too. Everything about the ignition is new. It can not be gasoline supply! How can I find the mistake?

we have a weird problem with a v8 engine. The engine does not run round, like a sack of potatoes. technically the engine is very very good. everything about the ignition is new. Coil, cap, candles, ignition cable, contacts, everything. with an electric sd1 ignition, the motor also runs not...

who knows companies that rebuild a differential good. I do not dare to go full throttle with the new 4.6 warrior engine ;-) once the thru-axle is already broken.

I have installed an electric petrol pump. At the same place were the mechanical was installed. but it seems like there will be no gasoline in the morning. the engine is running then he throttles out. but it already makes tak tak tak, very little. as if the carburetors are full with petrol...

my condenser is always broken after a few kilometers. then the engine starts to jerk. With a new condenser, he drives again 20-30 kilometers. what can be the cause? :-( Jorgen

I will soon install a strong 4.6 liter in my p6 with R380 5 speed gearbox. I have the 5 speed box already installed for some years with a normal sd1 clutch. I'm not satisfied with the clutch, it does not feel good, especially when approaching. Now I want a better clutch for the 4.6. Can you...

good evening everyone. are the differencial of 2000, 3500 o. 3500S identical or have they different ratios? best regards jorgen

Can I still drive a 4.6 liter engine with HIF6 o HIF44, or does it have to be the HS8? I don't want to install weber or something else! Regards Jorgen

Hi, I'm looking for a supplier of new leather seat covers. Regards Jorgen

Good Morning, Is it possible to install a p38 in the P6? - fits the intake manifold? - Does the exhaust manifold fit? -What about the front cover, a front cover of 3.5 can be used? - Fit the engine holder -.... all other questions I need to know

i have a 10: 5 engine, with composite gaskets. what must be down from the heads to get the old compression?

I have a P6 v8 Mk1 with a 5 gang r380 installed. no matter what ignition system I had installed in recent years (mallory unilite, sd1 or contacts) it worked badly! after a few minutes the car begins to jerky. the ignition partly partially altogether and then comes again. I have EVERYTHING...

Hi All, how can the piston pin removed? Do I have to press the pin in a vice between two nuts? Best Regads Jorgen

Hi All, I need two manifolds for the P6 3500 S. I'm from Germany, so the manifolds must be sent to Germany. Best Regards Jorgen Schumann Mail: iunknown@ngi.de

Hi All, we want to convert an automatic to a 5 Speed LT77. Witch number of revolutions per Kilomter / Mile has the speedometer? We need to build a translation-gearbox for the speedometer? Best Regard Jorgen

Good evening together. We have an original P6 V8 engine from '74, this has a CR of 9.25. We want to bring the to 10.5 (devour heads) . Did any of you good data with which we can calculate it? LG Jorgen

hi all, I changed my motor,0 flywheel I have taken from the old motor, the clutch is new and the motor silents are also new. I have vibration when accelerating from 1900 to 2100 rpm. the exhaust hangs well, and the joints of the drive shafts are well. I thought it is the propeller shaft, gearbox...