Search results

  1. G

    Fuel Injection

    I had forgotten how much of a pain the choke was. So fitted EFI. Hoping for smoother running and better economy!!
  2. G

    V8 RH Exhaust manifold.

    Bummer, Putting my engine back together, managed to break a lug off the right hand manifold. anyone got a good one spare? Jim.
  3. G

    RVC Tachometer

    Anyone got an RVC tacho for a V8. I'm running early SD1 dissy and my RVI tacho is erratic. Jim.
  4. G

    Jack Stowage

    Anyone got a 'photo of the jack in its home in the boot? I'd like it to look right. :D Jim.
  5. G

    UCA MOT

    Just been for MOT, passed with no advisories. Now taxed. As this will be its last disc, I'm thinking of leaving it in. Jim.
  6. G

    GRRRRR!!!

    All I need to get UCA ready for MOT is the speedo working. Because I.ve fitted the ZF transmission, I have no cable drive. So, I've ordered a drive from Dakota Digital. $299 plus postage. £216 total. Expensive, but not a bank breaker. Until it arrived in the good old UK. BETWEEN THEM...
  7. G

    Spotted in Queensland

    Couple of cars, a P4 a P6 and a classic Range Rover? On thr road to Bribie Island. Too big to put in a suitcase, and not sure of the conditions. Jim.
  8. G

    Bukskin bits

    I have got some good buckskin box-pleat front seats, door cards and "B" pillar covers. To complete I am after a rear seat and centre armrest, long front door armrests ( V8 type) and knee bins. All of course in buckskin. Anyone got any, or know where I can ask? Jim.
  9. G

    Rear wing rubbers

    Where and how do rubbers 364631 fit?
  10. G

    New carpet set

    Looking for advice. Anyone fitted a new carpet set, and can comment on quality? I have looked at these:- http://www.ebay.co.uk/itm/Rover-P6-Salo ... 35c361ad1f http://www.ebay.co.uk/itm/ROVER-P6-NEW- ... 19e69f5bf7 Or do I go to someone like Coverdale? Jim.
  11. G

    Windscreen fitting

    Help. I fitted my windscreen last week, but, I wasn't happy with the top corners. The stainless finishers weren't covered by the rubber at the top corners. The off side was worst. So I took it out again, bought a new rubber, and refitted it. Now its even worse!!! Both top corners are not...
  12. G

    Rechromed Uder-riders

    I have a pair of re-chromed under-riders going spare. Thought I'd offer them on here before xxx.bay. Any offers. Jim.
  13. G

    Fraser

    Just been listening to Radio 2. Fraser Kinghorn:- Economics Student. Classic Car Enthusiast. And now, Picker of Classic pop songs on Radio 2. :D :D :D Nice Fraser. Jim
  14. G

    Power steering hoses

    UCA 445J didn't have power steering, but she does now, Well nearly. Anyone got any pictures of the hose routing in front of the engine? Jim. :)
  15. G

    UCA 445J Lives!!

    UCA ( orca ) the shark has fired up!!! Not run for over 12 months. Now running SD1 heads, with composite gaskets, and timing cover, new rocker shafts, 3.9 cam. Didn't run for long because:- no exhaust, no fuel pipes, no cooling water, no trans. oil, air filters..etc. Just filled the float...
  16. G

    Power steering resevoir

    I am fitting power steering, to my V8. Question is where does the reservoir go? It looks like it should fit exactly opposite to the brake master reservoir, the 3 hole pattern is the same. Anyone know? Jim.
  17. G

    master cylinder.

    I know it is probably quite simple, but how is the master cylinder connected to the brake pedal?
  18. G

    Help!!

    Just taken the flywheel ( flexiplate ) off, to fit the new one for the ZF box, The fixings are different, the P6 has 6 holes on approx 60mm PCD The one for the ZF has 4 holes on approx 100mm PCD. At the moment don't know what to do.
  19. G

    ZF 4HP22

    Yes, I know it's not a new topic, but has anyone completed this conversion? I now have a Range Rover Classic box. I've started to strip it but can't get past the first two clutches. Any clues? I also have a BMW 525E box, in the same state of dissasembly. The A clutch is better in the RR box...
  20. G

    Rear discs

    Looks like thre cost of parts is on the rise?!?! http://www.ebay.co.uk/itm/EBC-REAR-BRAK ... 564c895ac7 Must be some mistake......
  21. G

    UCA 445J Project?!?

    Had my 3500 about 5 months now, welded both sill bottoms and "D" posts. Rear susp and drive removed. Finally got to paint under the rear.
  22. G

    Where can I get......

    Refurbing my rear calipers, very impressed with the engineering, Do these look 40 year old? Or have they been replaced at some time? 73000 on the clock, no reason to not belive it. Trouble is the cup pistons. The rewind piece is missing and the plating is n*c*ered. See picture 1. Are they...
  23. G

    UCA 445J

    Getting stuck into it now. Repaired the sills.stripped out the rear suspension and drive. Its been regularly oil sprayed, preserved it quite well, but what a mess!!!! The boot looks good from underneath, but when I was under and the light was on above, it was like The Sky At Night1 I need a...
  24. G

    Technical puzzle

    Picked this up years ago, and figured out what it was for. Anyone else got one or know what it is? The inscription reads :- "TO SET AT .010/.012 REMAX PAT APPLIED FOR" on one and "TO SET AT .014/.016 REMAX PAT APPLIED FOR" on the other.
  25. G

    V8 Auto. Rad.

    Anyone got a radiator for sale? Don't think mine is fit for recon, one bracket is badly bent and corroded and someone has sealed the drain?? One that needs a recore would do.
Back
Top