Search results

  1. clive P62

    Mocal PC1 Rover V8 Oil Pump Cover supply problem

    A couple of miles from me in Ashford middlesex, great place, used them for years.
  2. clive P62

    Rover P6 renewing project after 42 years barn live.

    Also 9 out of 10 heater matrixes are furred up / blocked
  3. clive P62

    LED HEADLIGHTS, my limted experience so far

    Standard Lucas sealed beams were 37/5 dipped and 50 watts main. Inner lamps were 50 watt and later were 75 watt as written on the outer lens.
  4. clive P62

    AED blanking plug thread

    Tap required is 5/8 UNF.
  5. clive P62

    AED blanking plug thread

    I will have a look later.
  6. clive P62

    SPRINGS - CAR SET OF FOUR V8

    On my NADA only 1 shim extra on the front and only on the N / S as this is the drivers side and A / C compressor on the N /S
  7. clive P62

    AED blanking plug thread

    I have a tap for that plug ,will have a look at what it is.
  8. clive P62

    Rebuilt Hybrid ZF 24/22 auto box

    Thanks Quattro I've did see the gearbox on EBay.
  9. clive P62

    Rebuilt Hybrid ZF 24/22 auto box

    Does somebody do a complete kit to fit these to a P6 ?
  10. clive P62

    10 bolt head upgrade

    I am not after a road rocket but something that when it's in top gear I can accelerate easily without kicking down.
  11. clive P62

    10 bolt head upgrade

    I will build a spare box just in case I rebuilt the diff a couple of years ago with new diff shafts and planet gears / shafts.
  12. clive P62

    10 bolt head upgrade

    Even though I have a Hurricane camshaft I am still undecided if I will fit it to my 4.6 which will be going in my P6 auto soon, It's only going to have S.Us but will have S manifolds + bespoke auto downpipes made to S size.
  13. clive P62

    Lower shock mount reinforcement plates.

    Thanks Ron ,wasn't sure if the lower part of the bracket did weld to the sides of the lower tie bar mount, then that makes the bracket at an angle to the top chassis if you know what I mean.
  14. clive P62

    BW35 Isolator Switch Setting

    Yes been caught out before with linkage adjustments.
  15. clive P62

    Lower shock mount reinforcement plates.

    I've got some lower front shock absorber reinforcement brackets I've had for ages and not fitted. I know roughly where they go but a close up picture would be nice if anybody can help. Thanks Clive.
  16. clive P62

    Interior retrims..... POST YOUR PICTURES

    Yes a bit like sandlewood seems many shades / armrests different to the seats
  17. clive P62

    Interior retrims..... POST YOUR PICTURES

    I had these done in the late 80s as even then I couldn't get a decent set
  18. clive P62

    SD1

    HWC is still about and running fine, he needs to come out of deep sleep
  19. clive P62

    SD1

    No not twin plenum but had a few mods . GDS 3 inch exhaust system with 1/78 4 into 1 manifolds. Mark Adams modified ecu to use jag 4.2 flow meter, rising rate fuel regulator and solid state fuel pump resistor. Standard camshaft, when rolling road tested produced 218 BHP, a very noticable...
  20. clive P62

    SD1

    Loved my vitesse .
  21. clive P62

    Electric steering pump in a V8

    Snap same one as I've got on my saxo
Back
Top