Search results

  1. Cherryroverp6

    New Project, 1966 2000 TC

    Hello vern, thanks! It's quite a great car. I'm sure it is a 66. I used parts off my 67/68 on it like the rostyles and bumpers because it needed them. I have the original rims as well as the chrome caps. This is vin 418 with the plate in the door jam.
  2. Cherryroverp6

    New Project, 1966 2000 TC

    Hello Everyone, Cherryroverp6 here, It has been quite a long time since I have posted onto these forums as I had to let my previous project go due to the bulk head rot. I ended up stripping my 68 2000 to the base unit an saving everything I could. I have Since acquired a 1966 2000 Tc that had...
  3. Cherryroverp6

    Hello there !

    Hello there !
  4. Cherryroverp6

    Drive shaft removal

    I'll have to post a picture later. It's a bit hard to explain, but that makes sense
  5. Cherryroverp6

    Drive shaft removal

    You are right about which shaft! It seems that the shaft bolts need to be held on both sides for the side towards the rear end. Perhaps one is loose
  6. Cherryroverp6

    Drive shaft removal

    Hello everyone, This evening I was attempting to remove the drive shaft to check the u joints while the transmission was out. Apon attempting to fit tools at the rear yoke towards the diff I was unable to fit a socket or even a wrench behind it without hitting up against the tube. Is there any...
  7. Cherryroverp6

    Rust air ducts..

    Hello everyone. Recently I discovered that my rovers air ducts from the heater box are riddled with rust and scale. It extends from the windshield air vents to the passages underneath the plastic dash under the speedometer. All the way into the box section unbove the foot well/ pedals. The...
  8. Cherryroverp6

    Clutch trouble!

    I was caught wind that sometimes they had premature clutch failure. She's got about 80,000 miles
  9. Cherryroverp6

    Clutch trouble!

    Hello everyone. I have yet another mechanic gremlin. I suspect a clutch failure as she slips in third/fourth gear especially up little hills as in the revs surge very high with no speed increase at anything above 35mph. The clutch grabs at the very tip top of the throw :/ as well. Someone...
  10. Cherryroverp6

    No start after setting valve timing

    Thank you. I got her running with new points and condenser!!
  11. Cherryroverp6

    No start after setting valve timing

    Yup I have points. I just ordered a set of points and condenser just encase
  12. Cherryroverp6

    No start after setting valve timing

    I'll check the leads. If this doesn't solve the issue what should I check next?
  13. Cherryroverp6

    No start after setting valve timing

    Hello everyone I've been continuing to try and find out why my 67 rover tc 2000 won't start. Ive set the timing to the EP mark on the flywheel to the camshaft. She no longer started after this. I've got compression and spark. Fuel, I proceeded to adjusting the distributor with no difference...
  14. Cherryroverp6

    Looking for proper wiring order on diz cap

    Hello everyone, I have a slight problem on my 67 Tc 2000.I am trying to find the true lead setup for the distributor cap. I am wondering what the true #1 cyl lead is on the cap. Here is a photo. Any help would be greatly appreciated. As per properly setup distributor with it set 6 degrees.
  15. Cherryroverp6

    Bad lower right ball joint removal?

    Last major issue I seem to be having with my rover is removing the ball joint as it is very worn. I can't seem to find a mechanic who can give me a good idea of how much labor it will take nor to time. Let alone a proper tool. I've been searching left and right for the proper ones. Any advice...
  16. Cherryroverp6

    Non functional rear calipers

    Did not have any fluid inside. Just a seized piston from sitting
  17. Cherryroverp6

    Non functional rear calipers

    I have good news everyone. But thank you for all of the very informative comments. I pulled the calipers and rotors. The left side was locked up and I was able to fanangle the pistons loose but have to unlock the stuck e brake rod on the left caliper. The right side was much easier to get freed...
  18. Cherryroverp6

    Non functional rear calipers

    Hello everyone. I currently have my p6 with girling Calipers on wheel ramps looking at them. My hand brake engages the mechasim on the calipers, but doesn't stop the car. I don't seem to be getting movement nor wear on the discs. The pads have plenty of meat left. And the brake pedal has very...
  19. Cherryroverp6

    New Here With my 1967 Rover tc 2000

    Thank you, I've come a long long way, Just need to find someone who can fit the new ball joint n brake calipers when i get them :)
  20. Cherryroverp6

    New Here With my 1967 Rover tc 2000

    Thank you !
  21. Cherryroverp6

    New Here With my 1967 Rover tc 2000

    Hello everyone, I am new to these forums an Excited to be a part of them. Almost a year ago I acquired a 1967 Rover Tc 2000 that had been sitting since 2000 in a back yard in Vermont USA. Before its Previous owner had fallen ill it was his pride an Joy and Now is mine. It came very rough with...
Back
Top