Hello all,
I've written this out for Retro Rides/Facebook so probably just easiest to cut and paste it to here:
Model: Rover P6 3500 Auto
Year: 1972
Mileage: 73850 - car still in use so rising slowly
MOT: Until September 2017
Location: Southend-on-Sea, Essex
Price: £2000
Contact details...
Sod it! It's going to the mechanics, I give up!
There's not really any reason why it shouldn't be at least running so I've come to the conclusion that whatever it is, if I haven't found it yet I'm not going to!
I reset the timing again today as it wasn't me that timed it last time, still...
Incredibly helpful post, thank you. I will get to that as soon as I can, hopefully will be able to do it tonight or one evening this week and won't have to wait til the weekend.
Thanks again for the photos etc, they'll be a huge help.
Will try this tomorrow night hopefully as long as I can get a pair of hands.
Aha! I knew I'd heard 2.5 turns from something, somewhere! Shame I decided to fabricate the rest of it.
Having trouble picturing this - because I took the carbs apart to replace the float needles/seats, a lot of...
Update! The car has now run, absolutely horribly, for a total of about one minute. So I'll call that progress.
Carbs with their new float needles/seats are on. What I said in the above post about 2.5 turns from all the way in was complete cobblers obviously and I've misread something, as it...
Right... So I got the carbs off, stripped them down and cleaned them out, and I have replaced the float needles and float needle valve seat things. Both sets of needles and seats were worn, so maybe this is it. All I have done so far in terms of setup is set both of the mixture screws to 2.5...
I'll fetch a pic over the weekend.had carbs off tonight, stripped them down part of the way. Float is intact in the one I've done, not too horrific in there but the float needle is quite scored. I've ordered up a pair of float needle kits and some new gaskets.
I'm going to take them to work and...
It's actually the ignition module that's catching on the stay bar.
The vac advance is in the same position, close to a water pipe, on your left looking into the bay from the front. The ignition module and the connector are what's in the way.
Re: moving it around - am I correct in thinking...
I mean more that it's flooding itself when you try to start still.
And yeah I am inclined to agree about the bar. A bit of a pickle because he had the same problem I did, that it wasn't possible to rotate the dizzy enough with the bar there.
I'd hope that there was some way to get it in time...
Huco pump fitted and working. Now need a real good tidy up of wiring and fuel pipes as I know the ignition system works.
To time the distributor correctly the mechanic removed the left hand (looking out from the cabin) stabiliser bar that attaches next to the distributor. I spoke to him tonight...
You're right, it is easy. The information was filtered through my mother who unfortunately does have a flair for the dramatic and a tendency to add her own spin to any information she passes on! Dad spoke to him also and was much more positive so we'll go with that!
I'll stick the pump on then inspect the floats and the rest of the carbs, see where it takes me. If the carbs look Ok inside, I will just reset them to standard at first.
Thanks for advice all, I'll work my way down that list.
I've ordered up a low pressure huco pump after searching on here to confirm which one, so will get that fitted as soon as I can. Even if it's what's overwhelming the carbs they'll still be well out of tune.
I guess it's a matter of finding out if it's just the floats, or a proper rebuild. There...
I wasn't available when the gent was round but he spoke to my dad - who will be around later this evening and I'll be grilling him.
All I can glean so far is that it was running very badly but the carbs were very poorly set up and set up differently to each other - and that he said carb...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.