Search results

Has anyone got a spare carburettor spacer/insulator with the lugs and throttle rod from an early series 1 2000 for sale?

There’s no fixing holes attached and the rear end has snapped off where the ashtray sits

Thanks for reply, it’s the radio console and the handbrake centre console I need. Is there a great difference between them over the years? Do you have any?

I’m looking for a good radio and handbrake centre console for my 1964 series 1. Can anyone help?

Can you put a close up of how the bonnet stay rod attaches at the front and how it clips to close bonnet. Mine has been bodged and have no idea how it should be. Thanks

The ones I was going to do up had a tab half way up the tube but had corroded off. Haven't looked at the ones on my car yet to see the difference

This has probably been discussed before but are all front struts the same between models? I have two old ones from a 2200sc that I was going to overhaul to fit to my early 2000 that has Dunlop brakes.

How is the drivers side front wing?

Black series two flat pleat rear seats for sale. One cushion has small split and all need a good clean. Offers please and collection only

Thanks all, if it turns out ok box will be for sale

Without stripping it down is there any way to check for wear?

The number seems to be stamped over, possibly recon.

I've got a gearbox I bought years ago along with a rover v8 engine I think it's an LT77 type. Can anyone confirm?

Spotted in Denny, central Scotland red P6 mk2 NLD???L. Anyone on here?

The tabs are only there to hold the springs in place so won't make any difference. With the new disc being slightly shorter it won't make any difference as there is less chance it will foul on anything. As long as the hub fits in the flywheel and the cover there will be no problem.

The Borg n beck numbers don't cross but each numbers are good for P6 but are no longer available according to sach website

I have two different carb spacer blocks one with the throttle rod lugs and one without are both fitted? Also on the heat shield there was a bracket broken on the bottom edge, where does that bolt onto?

Here's a link to the Glasgow Monte organisers site with a story of the start and pics of the cars. http://www.caledonianmsc.com

Thanks Harvey, looks like I've got more parts to add to my list. I'm sure the bearing sleeve has a rounded face so that's one thing I don't need :D

It's been two years since I removed my engine and gearbox and now trying to piece things back together. Firstly I need a new clutch, being a 1964 2000 with an 'A' suffix gearbox the clutch cover should be the one with the bearing shoulder on the fingers but has had a later one fitted, I can see...

Found this site with a break down of dizzy, doesn't help with position of drive dog but shows position of thrust washer on the 25d type. The 45d diagram has a nylon distance washer fitted inside below the weights so I imagine that's where it will go on my 25d...

I've stripped down the dizzy and have arsed up by not noting which way the drive dog was fitted. First glance I thought it was central but now see it is slightly offset. Has anyone got a pic or diagram so I get it right? Also there is a plastic seal and bronze shim do these go between dog and...

I'm rebuilding the carb from my 64 2000sc that I stripped down months ago and can't remember if the needle sits flush or goes right in to the piston. Flush or.... Right in. Also can anyone tell what is the correct needle, the kit had an RN needle but it was a KU needle that came out. And can...

My user name is year of birth not age :D . Just turned 47 at the start of the month. I had always liked the P5b coupe but the P6 just came about through somebody we know through work. The only time I've been in one before was when I was around 10 and a friends uncle took us for a run in his. I...

Thanks Peter, all pages came through no problem. Just need to get the car running now to play with it :D