Yes I know now I already have let it bore out to 30.02 mm witch is the diameter from the shaft of the gear box we are using . So I assume the box is not en originele box for the P6 . Because Harvey confirmed me the gear for the 35 en 65 are the same. Still had the 35 box, en took the gear out en...
Hi everyone en Harvey , I took out the gear of the 35 box en yes it's the same as I already have. So che won't fit also. I can take them to a machine chop tho bore them out it is only a 2 mm job. But if you look at the pictures I have made you will see that the right gear is one 1 mm larger in...
Hello,Is the gear ratio different between the two types of boxes. If it is the case are you going to run lower in RPM. I suspect this is going to be en other specialist anser for Harvey. Kind regards Marc.
Thank you Harvey, for your quick reply, didn't want to bother you again buy the phone. It's a little bit easier whit a picture tho explain. Keep well hope to hear you soon. Cheers mate .
Hi every body , would like to now your opinion on this tho torque converters. The one with wat I presume are cooling fans welded on was installed on a B&W 35 . The other was installed in a B&W 65 . The choold be the same models as Harvey said. In witch I have no doubt. But I need to overhaul one...
Hi Demetris, thank you for your reaction I am going to run the fan for a while to see how warm it is actually going to get . The foam chood be heat resistant . But in this case I want to be on the safe side . By closing the box I don't understand very well wat you mean . I thought the fan was...
Hi Peter I have bin thinking about that but the risk of ending up with a mes was to big . It is well blocked from everywhere en can not move anymore . Did a test en I have no loose of air . I think it's going to make a difference . Tomorrow I will reassemble the rest of the box . En then the...
Next I have found some foam witch can not rotten out you squeeze it in en til nothing can move anymore . Then you check the air gaps en you close them also with foam .
Next the adjustment of the fan in the new space . You are going to grind away some plastic to be chure it's flat on the bottom of the fan where the air intake is .
Hi everybody like i already promised I am going to put the pictures of the progress I am making on the swap of my fan for the heater box . Be free to give me your thoughts en a little help on the reconnection of the electric wires would be well appreciate . So her we go
Ok thank you , I am in need of more depth think around 20 mm but have the choice between the plate on the picture or the one in front with the round hole in it for me it looks the best to go for the rear plate because of the access . I thought that the fact the fan is already in a cage didn't...
Hi everybody, I am going to go for the 3 SPEED SQUIRREL CAGE HEATER FAN as propose in this topic it is looking as a good fit with only a small amount of adjustment . One plate is going to be cut out . But I have enough clearance to fit it like it is supposed to be . In the picture you see the...
I have both of them with clip en one with bold , today we did some testing with a Mitsubishi Colt fan en I think we are going to make en attempt to fit it . It's the right rotation and it is not so big . I will make pictures tho chow the way we attempt to fit it . Thank you very much everyone...
Hello I am going to look for a other solution do tho the fact that the flaps are in the opposite direction too . I am going to try a Mitsubishi fan. I hope to inform you al on that project.
Hopefully there is somebody out there who has done the conversion en can guide us out of this problem , any help would be appreciated ladies and gentlemen .
I don't know if the plate is very important you still have enough clearance at the back in the firewall . I am curious to see how this is going to end .
Hi cobra , I am going to take it can you give me your banc number en say how much I have to ad for the chipping . I am on fb en Messenger my email address is marc.verspecht@gmail.com
Kind regards Marc .
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.