hi does anyone know someone in romford or surrounding area that can supply and fit electronic ignition and come to me as I am looking to get one fitted to my 1964 rover p6 2000 sc
hi sorted tapet out shes runng well now need to ajust the cab witch is a standered su single carb does any one know how to ajust as mine is running far to rich and puffing out the excuste any help diagram or pitures will be very much appreciated
hi all
going to start the job of replacing nosy shim out tomorrow does any one known lady book of dos and donts so i dont get myself into any unnessery trouble and any digram or picture or the prosses to go through from start to finish would be most appresated
hi thank you GOOD NEWS!! got her fired up today run resonably well now has a nosey tappet so next job to clear that . i found out that i had a problem with the carb 2 videos on youtube showed me how to fix the problem...
hi all another day working on the rover and still have the same problem does anyone know where i can get another good working order cabareter or some where i can get mine recondtioned and does any one no or help on witch wat the dog sprocket at the bootom of the distribter ment to be...
hi thax for that ill have a go tomorrow i do no that i have a problem with the choke is not oprating proplley its really stiff witch is conected to the neddle wtich doest go up and down freely ill get on with it tomorrow and see whats going on as its getting cold out there ill keep you...
hi mate thanx a lot for that you have saved me a engine strip down if it is that ill take the carb of tomorrow and have a check as turning into one of these jobs i wish i never started loll thanx a lot john
hi mate thank you for that but i thank im going to have to strip her down as getting a lot of fuel in42 and 3 pistons so im wondering if i have done somthing wrong when i put the piston rings in more investagation thanx for all your help so far here are a couple of picture on the road last year
yes it goes anti clock wise should I set it up pointing to number 1 piston at the front of the engine and set the leads at 1342 ordo you have any pictures of where it should be pointing to thanx john
hi thanx or your message what i done was i drove her into the garage i unbolted the head put the timeing on to top dead center without pegging the cam shaft in i then unbolted thead took the cam out then the cups 1 by 1 wth the shims that where there and placed in a line on the bench
i then...
hi i just noticed your anwer im getting about thimble full and it is wetting up the spark plugs when i take the spark plugs out and clean them and drain the fuel with a seringe she will start for a few second but then i have to repete the prosess this has all started since i put...
hi thank you would that be the cause off petrol on top o the pitons and what is the easyist way of checking valve clearance as i said engines are not my strongest point cheers john thanx for all your help
hi mate i have put it all back it did try to fire up after i put it on ep mark and it ran for a short time ive put the firing order as 1342 but it wouldnt even atempet to fire
i have moved the leads around one at a time and it coughs and splutters but now i have discovered that i am...
thank you for that great help ill give it a go on wed and ill get back to you and let you no how it went thanx for your help as im more body work than engine work bit of lack of nolage in that area cheers john
hi thanx for your reply it is both vale and ignition timing iv tryed the 1342 anti clock wise starting with 1 at the front of the engine and cam timing does the in let or the excuste have to be down on the cam timing or both shut thanx john
hello i have a rover p6 1964 serice 1 sc 2000 i have put new piston rings in as it used to smoke i put the engine back together and back in to the car i seam to be having problems of timining it up i have a haynes manuil on it but it is confusing does any body have a lady book instrution...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.